Beschreibung

Übersicht & Stromversorgung

The Sinergy BATSIN12-26 represents the pinnacle of compact power engineering, delivering unmatched starting amperage and sustained deep-cycle resilience in a standardized 12-volt enclosure. Constructed with high-density lead-calcium-tin alloy plate grids, this battery significantly suppresses internal resistance to accelerate electron transfer during high-amperage draw events. Whether turning over high-compression small engines in extreme winter conditions or sustaining critical auxiliary loads, the BATSIN12-26 ensures exceptional cell balance and constant voltage stability throughout its duty cycle.

Vibration is one of the primary catalysts for internal cell degradation, plate buckling, and active paste shedding. To counteract these stresses, Sinergy implements tightly compressed Absorbent Glass Mat (AGM) separators that micro-porously immobilize the liquid sulfuric acid electrolyte. This reinforced structural envelope shields internal elements from the punishing harmonic vibrations produced by lawn tractors, small plant machinery, powersports machines, and commercial utility vehicles, effectively tripling service life compared to traditional flooded alternatives.

Operating as a fully sealed Valve-Regulated Lead-Acid (VRLA) platform, the BATSIN12-26 features a self-regulating, pressure-controlled safety valve system with internal gas recombination efficiency exceeding 99%. This closed loop virtually eliminates water loss, negating the need for electrolyte top-ups while allowing mounting orientations of up to 90 degrees without risk of acid leakage, terminal corrosion, or chassis degradation.

Technische Daten

Fahrzeugkompatibilität und Anforderungen an Start-Stopp-Systeme

The Sinergy BATSIN12-26 is widely deployed across specialized automotive auxiliary installations, commercial lawnmowers, utility terrain vehicles (UTVs), golf caddy systems, mobility platforms, and high-spec powersports machinery. Its robust cyclic performance allows it to handle modern parasitical drains, including tracking units, onboard telemetry, and active safety accessories, without falling into deep sulfation states.

For micro-hybrid and start-stop vehicles, the BATSIN12-26 is uniquely qualified to serve as an auxiliary or backup battery. Modern automotive architectures utilize dedicated secondary batteries to isolate and sustain sensitive cabin electronics, dynamic braking computers, and steer-by-wire modules during engine-off phases. The ultra-low internal resistance of the BATSIN12-26 provides rapid dynamic charge acceptance (DCA), allowing the vehicle’s alternator and regenerative braking systems to recover consumed energy quickly within truncated drive cycles.

Anleitung zur Installation und Pflege

To maximize service life, proper installation procedure must be observed. Always inspect the mounting tray to confirm it is free of dirt, debris, and sharp contours. Clean the battery terminal pads and cable leads using a bronze wire brush to eliminate oxidation layers before installation. Secure the positive (+) lead first, followed by the negative (-) chassis ground, tightening hardware strictly to manufacturer torque ratings (typically 4.5 to 6.0 Nm) to avoid stripping internal lead threads.

Because AGM technology utilizes dense glass fleece mats, it is critical never to expose the unit to charging voltages in excess of 14.7V at room temperature. For off-season vehicle storage, disconnect the negative terminal or install a microprocessor-controlled smart trickle charger that features an AGM-specific maintenance float profile (13.5V to 13.8V). Store the battery in a cool, dry environment between 10°C and 20°C to mitigate ambient self-discharge.

Häufig gestellte Fragen (FAQs)

Ist diese Batterie für Start-Stopp-Fahrzeuge geeignet?

The Sinergy BATSIN12-26 is ideally designed to serve as an auxiliary or secondary buffer battery in modern start-stop and hybrid vehicles. However, it is not engineered to act as the primary starter battery for large multi-cylinder internal combustion passenger vehicles requiring 600+ CCA.

Does the Sinergy BATSIN12-26 require topping up with acid or water?

No. This battery uses maintenance-free VRLA AGM technology. The internal electrolyte is completely absorbed into glass mat separators, and the oxygen recombination cycle prevents fluid depletion throughout its operational life.

Can I mount this battery on its side?

Yes. Because the electrolyte is fully absorbed in micro-fiber mats and the casing is sealed with pressure-release safety valves, the battery can be mounted upright or tilted up to 90 degrees without fluid leaks or performance degradation. Inverted mounting is not recommended.

What type of charger should I use with this AGM battery?

You must use a multi-stage intelligent electronic charger compatible with AGM/VRLA batteries. Conventional unregulated chargers can deliver excessive voltage spikes above 15V, causing the safety valves to vent and permanently drying out the internal cells.

What is the expected shelf-life and self-discharge rate?

Due to ultra-pure lead-calcium grid chemistry, the BATSIN12-26 has an exceptionally low self-discharge rate of less than 3% per month at 20°C. It can be safely stored for up to 6 months before requiring a conditioning charge.

Zusätzliche Informationen