Περιγραφή

Επισκόπηση & Παροχή ισχύος

The Sinergy BATSIN12-14H 12V 14Ah AGM DC battery represents the cutting edge of valve-regulated lead-acid (VRLA) engineering, developed specifically for dual-purpose cyclic discharge and high-rate starting applications. By utilizing premium ultra-thin Absorbent Glass Mat (AGM) micro-fiber separators, all internal acid electrolyte is fully bound within the separator pores. This dry-cell architecture eliminates free-floating liquid, guarantees 100% spill-proof operation at any mounting angle, and yields dramatically lower internal resistance compared to traditional flooded or standard gel batteries.

Constructed with high-density, virgin lead-calcium-tin alloy grids, this 14Ah energy source minimizes positive grid growth and thermal degradation during intensive charge-discharge cycles. The compressed plate packs provide superior structural integrity, absorbing destructive shock and continuous engine vibration up to four times more effectively than conventional lead-acid options. This robust internal reinforcement protects active plate material from shedding, ensuring stable voltage profiles, superior energy throughput, and significantly prolonged service longevity.

Cold-weather starting reliability is an engineered strength of the Sinergy BATSIN12-14H. Because internal electrical resistance is minimized, the battery achieves instantaneous power delivery and high cold cranking amperage even in freezing sub-zero ambient temperatures. Concurrently, an integrated valve-regulated pressure relief system maintains continuous oxygen and hydrogen gas recombination at greater than 99% efficiency, preventing dry-out, eliminating toxic acid spray, and preventing terminal post oxidation over the battery’s entire operational lifecycle.

Τεχνικές προδιαγραφές

Συμβατότητα οχημάτων και απαιτήσεις συστήματος Start-Stop

In modern micro-hybrid and contemporary luxury passenger vehicles, auxiliary power packs play an indispensable role in vehicle stability. Vehicles manufactured by BMW, Mercedes-Benz, Volvo, and Audi utilize dedicated 12V 14Ah secondary batteries to safeguard critical electronic control units (ECUs), lane-keeping sensors, electro-hydraulic braking systems, and transmission solenoids while the internal combustion engine is paused during auto-start-stop events. The Sinergy BATSIN12-14H satisfies these rigorous auxiliary performance demands, buffering electrical bus loads and eliminating transient voltage drops that cause diagnostic fault codes.

Beyond automotive auxiliary integration, the BATSIN12-14H serves as a primary high-output starting battery for touring motorcycles, adventure bikes, snowmobiles, ATVs, and side-by-side UTVs equipped with high-compression engines. These demanding powersports applications require instantaneous burst amperage to fire modern multi-cylinder configurations, combined with steady cyclic reserve to support auxiliary lighting, winches, heated grips, and GPS navigation units. The deep cycle designation (DC) guarantees that repeated shallow or moderate draw cycles will not prematurely degrade cell capacity.

Οδηγίες εγκατάστασης και φροντίδας

Prior to mounting the Sinergy BATSIN12-14H, make certain the vehicle ignition and all electrical accessories are completely turned off. Clean the vehicle connector cables and terminal posts thoroughly using an abrasive wire terminal brush to guarantee bare-metal contact and prevent parasitic resistance. When connecting the unit, attach the positive red cable first, followed by the negative ground cable to eliminate the risk of accidental short-circuit arcs. Tighten the terminal hardware firmly to 4.5 to 5.0 Newton-meters of torque, avoiding over-tightening which could crack the terminal collar.

Recharging must always be executed using a multi-stage intelligent battery charger programmed with an AGM-specific charging profile. Maintain standard absorption voltage between 14.4V and 14.7V at 25 degrees Celsius, with float charging set between 13.5V and 13.8V. The charging current should not exceed 3.5 Amps (roughly 25% of rated capacity) to prevent localized plate heating. For seasonal storage during off-season months, fully recharge the battery and store it in a cool, dry area away from direct sunlight, connecting a micro-processor float maintainer to counteract seasonal self-discharge.

Συχνές Ερωτήσεις (FAQ)

Can the Sinergy BATSIN12-14H be used as a start-stop auxiliary battery?

Yes. The Sinergy BATSIN12-14H is specifically built with AGM valve-regulated technology that matches the voltage stabilization and fast-acceptance recharge profiles required by luxury automotive auxiliary start-stop circuits.

Can this AGM battery be mounted in non-vertical orientations?

Yes, because the electrolyte is fully absorbed and locked inside micro-porous glass mat separators, the BATSIN12-14H is non-spillable and can safely be mounted upright or tilted on its side without any danger of acid leakage.

Does this battery ever require distilled water top-ups?

No. The Sinergy BATSIN12-14H is completely sealed and 100% maintenance-free. Its internal catalytic recombination cycle converts gas back into water continuously, meaning the casing is permanently factory-sealed and must never be opened.

What is the ideal charging current for this 14Ah AGM battery?

The optimal charging current is between 1.0 Amp and 1.4 Amps (0.1C rate), with an absolute maximum safe limit of 3.5 Amps. Always use a dedicated smart AGM charger equipped with automatic stage regulation.

What steps are needed to prepare this battery for winter storage?

Before storing for winter, charge the battery to 100% capacity and either disconnect the negative terminal or place it on a continuous smart float maintainer in a dry, temperate environment above freezing.

Επιπλέον πληροφορίες